REC615 and RER615 Modbus Point List Manual - Grid automation - Modbus Communication Manual - Modbus Point List Manual - REC615 Grid Automation - RER615 Grid Automation Protection and Control - Relion Product Family - 2.0 - IEC - ANSI - 16.06.2023 - REC615 and RER615
REC615 and RER615 Modbus Point List Manual
Copyright
Disclaimer
Conformity
Introduction
This manual
Intended audience
Product documentation
Product documentation set
Document revision history
Related documentation
Symbols and conventions
Symbols
Document conventions
Functions, codes and symbols
Modbus data mappings
Overview
Supported functions
Supported functions in REC615
Supported functions in RER615
Indications
Common data 1
LD0.ATSABTC1 Automatic transfer switch (1)
CTRL.CBCILO1 Circuit breaker enable signals (1)
CTRL.CBCSWI1 Circuit breaker (1) mom. position
CTRL.CBCSWI1 Circuit breaker (1) mom+mcd position
CTRL.CBXCBR1 Circuit-breaker control (1)
LD0.CMHAI1 Current total demand distortion (1)
LD0.CMMXU1 Three-phase current measurement (1)
LD0.DARREC1 Autoreclosing state (1)
LD0.DARREC1 Autoreclosing (1)
CTRL.DCXSWI1 Disconnector control (1)
CTRL.DCXSWI2 Disconnector control (2)
CTRL.DCXSWI3 Disconnector control (3)
CTRL.DCXSWI4 Disconnector control (4)
CTRL.DCXSWI5 Disconnector control (5)
CTRL.DCXSWI6 Disconnector control (6)
CTRL.DCXSWI7 Disconnector control (7)
CTRL.DCXSWI8 Disconnector control (8)
LD0.DEFHPDEF1 Directional earth-fault protection, high stage (1)
LD0.DEFHPDEF2 Directional earth-fault protection, high stage (2)
LD0.DEFHPDEF3 Directional earth-fault protection, high stage (3)
LD0.DEFHPDEF4 Directional earth-fault protection, high stage (4)
LD0.DEFLPDEF1 Directional earth-fault protection, low stage (1)
LD0.DEFLPDEF2 Directional earth-fault protection, low stage (2)
LD0.DEFLPDEF3 Directional earth-fault protection, low stage (3)
LD0.DEFLPDEF4 Directional earth-fault protection, low stage (4)
LD0.DPHHPDOC1 Three-phase directional overcurrent protection, high stage (1)
LD0.DPHHPDOC2 Three-phase directional overcurrent protection, high stage (2)
LD0.DPHHPDOC3 Three-phase directional overcurrent protection, high stage (3)
LD0.DPHHPDOC4 Three-phase directional overcurrent protection, high stage (4)
LD0.DPHLPDOC1 Three-phase directional overcurrent protection, low stage (1)
LD0.DPHLPDOC2 Three-phase directional overcurrent protection, low stage (2)
LD0.DPHLPDOC3 Three-phase directional overcurrent protection, low stage (3)
LD0.DPHLPDOC4 Three-phase directional overcurrent protection, low stage (4)
LD0.DPSRDIR1 Directional positive seq power (1)
LD0.DPSRDIR2 Directional positive seq power (2)
LD0.DTMGAPC1 Daily timer function (1)
LD0.DTMGAPC2 Daily timer function (2)
CTRL.ESSXSWI1 Earthing switch indication (1)
CTRL.ESSXSWI2 Earthing switch indication (2)
CTRL.ESSXSWI3 Earthing switch indication (3)
CTRL.ESSXSWI4 Earthing switch indication (4)
CTRL.ESSXSWI5 Earthing switch indication (5)
CTRL.ESSXSWI6 Earthing switch indication (6)
CTRL.ESSXSWI7 Earthing switch indication (7)
CTRL.ESSXSWI8 Earthing switch indication (8)
LD0.EFHPTOC1 Non-directional earth-fault protection, high stage (1)
LD0.EFIPTOC1 Non-directional earth-fault protection, instantaneous stage (1)
LD0.EFLPTOC1 Non-directional earth-fault protection, low stage (1)
LD0.EFPADM1 Admittance-based earth-fault protection (1)
LD0.EFPADM2 Admittance-based earth-fault protection (2)
LD0.EFPADM3 Admittance-based earth-fault protection (3)
LD0.FDEFLPDEF1 Directional earth-fault protection, low stage (1)
LD0.FDEFLPDEF2 Directional earth-fault protection, low stage (2)
LD0.FDPHLPDOC1 Three-phase directional overcurrent protection, low stage (1)
LD0.FEFLPTOC1 Non-directional earth-fault protection, low stage (1)
LD0.FPHLPTOC1 Three-phase non-directional overcurrent protection, low stage (1)
LD0.FPDHLPDOC2 Three-phase directional overcurrent protection, low stage (2)
LD0.FRPFRQ1 Frequency protection (1)
LD0.FRPFRQ2 Frequency protection (2)
LD0.GSELPRT1 Goose supervision (1)
LD0.HAEFPTOC1 Harmonics-based earth-fault protection (1)
LD0.IL1TCTR1 Three-phase CT supervision (1)
LD0.IL1TCTR2 Three-phase CT supervision (2)
LD0.INRPHAR1 Three-phase inrush detector (1)
LD0.INTRPTEF1 Transient/intermittent earth-fault protection (1)
LD0.LEDGGIO1 Indication LED states OFF/ColorX
LD0.LEDGGIO1 Indication LED states Color1/Color2
LD0.LEDPTRC1 Global conditioning (1)
LD0.LSHDPFRQ1 Load-shedding and restoration (1)
LD0.LSHDPFRQ2 Load-shedding (2)
LD0.MAPGAPC1 Multipurpose protection (1)
LD0.MAPGAPC2 Multipurpose protection (2)
LD0.MAPGAPC3 Multipurpose analog protection function (3)
LD0.MAPGAPC4 Multipurpose analog protection function (4)
LD0.MAPGAPC5 Multipurpose analog protection function (5)
LD0.MAPGAPC6 Multipurpose analog protection function (6)
LD0.MDSOPT1 Runtime counter for machines and devices (1)
LD0.MFADPSDE1 Multifrequency admittance-based earth-fault protection (1)
LD0.MFADPSDE2 Multifrequency admittance-based earth-fault protection (2)
LD0.MVGAPC1 Move (8 pcs) (1)
LD0.MVGAPC2 Move (8 pcs) (2)
LD0.MVGAPC3 Move (8 pcs) (3)
LD0.MVGAPC4 Move (8 pcs) (4)
LD0.MVGAPC5 Move (8 pcs) (5)
LD0.MVGAPC6 Move (8 pcs) (6)
LD0.MVGAPC7 Move (8 pcs) (7)
LD0.MVGAPC8 Move (8 pcs) (8)
LD0.NSPTOC1 Negative-sequence overcurrent protection (1)
LD0.NSPTOC2 Negative-sequence overcurrent protection (2)
LD0.NSPTOV1 Negative-sequence overvoltage protection (1)
LD0.PDNSPTOC1 Phase discontinuity protection (1)
LD0.PHQVVR1 Voltage variation (1)
LD0.PHHPTOC1 Three-phase non-directional overcurrent protection, high stage (1)
LD0.PHIPTOC1 Three-phase non-directional overcurrent protection, instantaneous stage (1)
LD0.PHIPTOC2 Phase overcurrent protection, instantaneous stage (2)
LD0.PHLPTOC1 Three-phase non-directional overcurrent protection, low stage (1)
LD0.PHPTOV1 Three-phase overvoltage protection (1)
LD0.PHPTOV2 Three-phase overvoltage protection (2)
LD0.PHPTOV3 Three-phase overvoltage protection (3)
LD0.PHPTUC1 Phase undercurrent protection (1)
LD0.PHPTUC2 Phase undercurrent protection (2)
LD0.PHPTUV1 Three-phase undervoltage protection (1)
LD0.PHPTUV2 Three-phase undervoltage protection (2)
LD0.PHPTUV3 Three-phase undervoltage protection (3)
LD0.PSPTUV1 Positive-sequence undervoltage protection (1)
LD0.PHSVPR1 Voltage presence (1)
LD0.PHSVPR2 Voltage presence (2)
LD0.RESCMMXU1 Residual current measurement (1)
LD0.RESTCTR1 Residual CT supervision (1)
LD0.RESVMMXU1 Residual voltage limit supervision (1)
LD0.ROVPTOV1 Residual overvoltage protection (1)
LD0.ROVPTOV2 Residual overvoltage protection (2)
LD0.SCEFRFLO1 Fault locator (1)
LD0.SECRSYN1 Synchronism and energizing check (1)
LD0.SEQSPVC1 Fuse failure supervision (1)
LD0.SSCBR1 Circuit-breaker condition monitoring (1)
LD0.SSCBR2 Circuit-breaker condition monitoring (2)
LD0.SPCGAPC1 Generic control point (16 pcs) (1)
LD0.SPCGAPC2 Generic control point (16 pcs) (2)
LD0.SPCLGAPC1 Local generic control points (1)
LD0.SPCRGAPC1 Remote generic control points (1)
LD0.T1PTTR1 Three-phase thermal protection for feeders, cables and distribution transformers (1)
LD0.TRPPTRC1 Master trip (1)
LD0.TRPPTRC2 Master trip (2)
LD0.TCSSCBR1 Trip circuit supervision (1)
LD0.TCSSCBR2 Trip circuit supervision (2)
LD0.ULTVTR1 Three-phase VT supervision (1)
LD0.ULTVTR2 Three-phase VT supervision (2)
LD0.VMHAI1 Voltage total harmonic distortion (1)
LD0.VMMXU1 Three-phase voltage measurement (1)
LD0.VMMXU2 Three-phase voltage measurement (2)
LD0.VSQVUB1 Voltage unbalance (1)
LD0.WPWDE1 Wattmetric-based earth-fault protection (1)
LD0.WPWDE2 Wattmetric-based earth-fault protection (2)
LD0.WPWDE3 Wattmetric-based earth-fault protection (3)
LD0.XAGGIO130 Physical I/O states (AIM card XA130)
LD0.XARGGIO130 RTD inputs (1)
LD0.XGGIO130 Physical I/O states (BIO card X130)
LD0.XGGIO120 Physical I/O states (AIM card X120)
LD0.XGGIO110 Physical I/O states (BIO card X110)
LD0.XGGIO100 Physical I/O states (PSM card X100)
Registers
User-definable registers [Alt.1], visible on 3x and 4x
User-definable bits [Alt.2], visible on 0x,1x,3x and 4x
SSR1 System status register (1) device health
SSR2 System status register (2) protection relay's mode and state
SSR3 System status register (3) data available 1 (client-dependent)
SSR4 System status register (4) data available 2 (client-dependent, user-definable)
SSR5 System status register (5) device alive register
SSR6 System status register (6) control command status (client-dependent)
Indication bits mirrored in registers
CTRL.CBCSWI1 Circuit breaker operation counter (1)
LD0.CMHAI1 Current total demand distortion (1)
LD0.CMMXU1 Three-phase current measurement (1)
LD0.CSMSQI1 Sequence current measurement (1)
LD0.DARREC1 Autoreclosing values (1)
LD0.DARREC1 Autoreclosing counters (1)
LD0.FMMXU1 Frequency measurement (1)
LD0.FMMXU2 Frequency measurement (2)
LD0.MDSOPT1 Runtime counter for machines and devices (1)
LD0.MVI4GAPC1 Integer value move (1)
LD0.MVI4GAPC2 Integer value move (2)
LD0.PEMMXU1 Three-phase power and energy measurement (1)
LD0.PEMMXU2 Three-phase power and energy measurement (2)
LD0.PHQVVR1 Voltage variation (1)
LD0.RESCMMXU1 Residual current measurement (1)
LD0.RESVMMXU1 Residual voltage measurement (1)
LD0.SECRSYN1 Synchronism and energizing check (1)
LD0.SCA4GAPC1 Analog value scaling (1)
LD0.SCA4GAPC2 Analog value scaling (2)
LD0.SCA4GAPC3 Analog value scaling (3)
LD0.SCA4GAPC4 Analog value scaling (4)
LD0.SCA4GAPC5 Analog value scaling (5)
LD0.SCA4GAPC6 Analog value scaling (6)
LD0.SCA4GAPC7 Analog value scaling (7)
LD0.SCA4GAPC8 Analog value scaling (8)
LD0.SCA4GAPC9 Analog value scaling (9)
LD0.SCA4GAPC10 Analog value scaling (10)
LD0.SCA4GAPC11 Analog value scaling (11)
LD0.SCA4GAPC12 Analog value scaling (12)
LD0.SPEMMXU1 Single-phase power and energy measurement (1)
LD0.SPEMMXU2 Single-phase power and energy measurement (2)
LD0.SSCBR1 Circuit-breaker condition monitoring (1)
LD0.SSCBR2 Circuit-breaker condition monitoring (2)
LD0.T1PTTR1 Three-phase thermal protection for feeders, cables and distribution transformers (1)
LD0.VMHAI1 Voltage total harmonic distortion (1)
LD0.VMMXU1 Three-phase voltage measurement (1)
LD0.VMMXU2 Three-phase voltage measurement (2)
LD0.VSMSQI1 Sequence voltage measurement (1)
LD0.VSMSQI2 Sequence voltage measurement (2)
System diagnostic values
Control structure 1
Control structure 2
Control structure 3
Control structure 4
Control structure 5
Control structure 6
Control structure 7
Control structure 8
Device ID string
Protection relay's real-time clock (in local time mode) - read and write (synchronize)
Protection relay's real-time clock (in UTC time mode) - read and write (synchronize)
Active parameter setting group - read and write
Event record structure
Fault record structure header
Fault record
LD0.FLO1RFRC1 Fault locator registrations (1)
LD0.XARGGIO130 RTD inputs (1)
Controls
Reset, acknowledge and trigger points
LD0.LDEV1 Protection relay's warm reset (1)
CTRL.CBCSWI1 Circuit breaker control (1)
CTRL.DCXSWI1 Disconnector control (1)
CTRL.DCXSWI2 Disconnector control (2)
CTRL.DCXSWI3 Disconnector control (3)
CTRL.DCXSWI4 Disconnector control (4)
CTRL.DCXSWI5 Disconnector control (5)
CTRL.DCXSWI6 Disconnector control (6)
CTRL.DCXSWI7 Disconnector control (7)
CTRL.DCXSWI8 Disconnector control (8)
LD0.SSCBR2 Circuit-breaker condition monitoring (2)
LD0.SRGAPC1 Set-reset (8 pcs) (1)
LD0.SRGAPC2 Set-reset (8 pcs) (2)
LD0.SPCGAPC1 Generic control point (16 pcs) (1)
LD0.SPCGAPC2 Generic control point (16 pcs) (2)
LD0.SPCRGAPC1 Remote generic control points (1)
Glossary